Custom LED Door Projector Courtesy Puddle Logo Lights
$89.95
Note: Turn around time on Custom LED Door Projector Courtesy Logo Lights is 3 to 4 weeks.
For Wholesale Prices – Please Call 773-583-3770
For No-Fade and Always On LED Glass Door Projectors- Click Here
Custom Projector Puddle Lights
Your custom logo or image will be lit up for everyone to see! Powered by an intense 7W LED CREE bulb, the Custom LED Door Projector Courtesy Puddle Logo Lights vividly project your favorite logo onto any floor surface. When you open your vehicle’s door, your custom image will help you see where you are about to step and sure catch the eye of onlookers.
Although meant to be mounted underneath a car door, these Custom LED Door Projector Courtesy Puddle Logo Lights have a wide variety of applications from accenting your engine bay, to your footwell.
Note: These projectors must be wired up to the nearest 12 volt light that goes on when the doors open and is usually factory installed in the door already. Drilling a single hole into the door panel is required (drill bit is included). The time required is usually 30-45 minutes per door.
Package includes: 2 LED Door Projectors & 1 drill bit
*There is an additional $50 Graphic Design Art Fee if you want our design team to completely create a new design for you from scratch.
**The acceptable file formats are jpg, png, pdf, eps or ai.
***Turn around time on Custom LED Door Projector Courtesy Logo Lights is 3 to 4 weeks.
****The image is intended to switch on and off. Keeping them on for more than 5 mins at a time could fade the image.
1 review for Custom LED Door Projector Courtesy Puddle Logo Lights
Add a review
Instructions for Installing Ghost Shadow Lights
The general steps are the same for every car, though some details may vary. Installing ghost shadow lights isn't too tough. It's just important to take note of what materials and equipment are needed, and to be careful with each step.
Turn off the Power Light
To conserve energy and keep the power light from running out during installation, use a screwdriver to lock in the door lock mechanism. This is generally found on the side of the door. This will effectively keep the power light from coming on when the door is open.
Remove the Door Panel
Put on safety goggles and protective gloves prior to beginning. The next step in installing ghost shadow lights is always to remove the door panel. The exact method varies from car to car, but usually involves first removing the trim (handle, window roller, etc), then removing screws with an appropriately sized screwdriver. Lastly, unlatch the pop clips by gently pulling, and the door panel should be able to be removed.
Drill a Hole for the Ghost Shadow Light
Choose a spot for the logo light in the bottom of the door panel that's facing the ground. Ideally, this location should be flat. Using a cordless drilland compatible drill bit, establish a hole the same diameter as the ghost shadow light's lens. To ensure the diameter is the same, measure the drill bit and lens diameter before drilling. For example, a one-inch drill bit could be needed. Wipe off any excess debris before continuing.
Set the Ghost Shadow Light into the Hole
Get the courtesy light (ghost shadow light). Set it into the hole that's just been drilled, then secure the light into the location by tightening the screws. Note that these courtesy lights typically come with retaining screws to secure the light; these will hold the light into place. Wire the Ghost Shadow Light into the Door Light
Tap into the existing wires in the door panel to light up the ghost shadow light. Remove the insulation tape covering the wires with a screwdriver or craft knife. Once the insulation tape has been pushed back, split the wires apart. Then take the wire cutter and strip the rubber off the two wires so that the interior copper metal is showing; do this same thing with the wires on the light. Then, tie the logo light wire into the car door's two light wires by wrapping it around the two wires gently.
Test the Ghost Shadow Light
First, turn on the power light and then test to see if the courtesy light comes on with the rest of the lights when the door is opened. If it does, it's time to cover the wires with electrical tape. Reinstall the Door Panel
Reinstall the door panel and lock in the pop clips, but wait to use the screwdriver. If any extra wire is hanging below the door, slip it up inside the door panel. Check to make sure all the buttons and lights are working as they should, and then screw the door panel back in securely. Repeat the Process for Other Doors
If desired, install a ghost shadow light on the opposite door. Many believe an even number (two or four) of ghost shadow lights looks best.
Related products
LED Logo Door Projector Lights
LED Logo Door Projector Lights
LED Logo Door Projector Lights
LED Logo Door Projector Lights
LED Logo Door Projector Lights
LED Logo Door Projector Lights
LED Logo Door Projector Lights
Mercedes Benz LED Door Projector Courtesy Puddle Logo Lights
LED Logo Door Projector Lights
Ron –
How long does it take to have custom door projectors made.
Mr. Kustom –
The custom door projectors take about 2 to 3 weeks to be manufactured after you approve your design.
Bobby –
Can you make a custom puddle light to fit a 2015 MKZ
Mr. Kustom Support (verified owner) –
Sure we can 🙂 we can do any type of custom logo for car to truck
NOLAN –
I WANT A CUSTOM LOGO? FOR LEXUS OF COOL SPRINGS
Rich Korber –
please contact our internet department for more information. we have made many custom dealer door projectors in the past.It is an inexpensive marketing and advertising tool. We just finished 500 sets for Dominoes Pizza.
Internet Manager / Richard Korber 773-230-4024 MR KUSTOM CHICAGO
Robert Pastorello (verified owner) –
I would like to get a puddle light made with Underdog logo can you make it?
Mr. Kustom Support (verified owner) –
I guess we already in process on making your door projector light congrats
kenneth matlock –
i have ghost lights already and would like just a custom lense made. i have the logo already, can you help me out?
Mr. Kustom Support (verified owner) –
Hello Kenneth,
We dont sell just the lense you need to get the whole set please call 773-583-3770.
Rob –
I would like to have the Dodge 100th Anniversary logo made in to a projector, any way this is possible?
Mr. Kustom Support (verified owner) –
Hi Rob,
Yes its possible please call 773-583-3770 to get more information and to place an order. Thanks
Roger Shumaker –
Would like to know if The Pontiac Fiero Logo (S) available? If not I am able to send a logo. However can the lens in the projectors be changed up or do I have to order a separate projector per design. If I was wanting to mix it up a little for different occasions?
Mr. Kustom Support (verified owner) –
It will separate projector per design. no we only have the pontiac logo. But we can make any type of logo.
Jim –
I have the logo I want made into a puddle light- but can I choose the colors to be included in the logo or is it just one color?
Mr. Kustom Support (verified owner) –
Hello Jim,
You can have any color you want.
Jesse –
Do the lights come with everything you need to install them?
Mr. Kustom Support (verified owner) –
Yes it includes everything you need.
cody –
are these 70$ for a pair? or each?
Shannon –
I have my Co. logo i want made in the puddle light. I have seen the ones you can swap out made for the land rovers. Do you make those or just the ones you have to drill?
Mr. Kustom Support (verified owner) –
we make those as well please call 773-583-3770
Jesse –
I want order 100 custom door projectors. Is the price then 29,95$ per piece? Can you say how much shipping cost to Finland and how many days does it take?
Mr. Kustom Support (verified owner) –
Yes for 100 or more the price is 29.95 a set which comes two lights in a set. Please call 773-583-3770 to get more info on shipping.
Jj –
Do you have an email I can send you a logo I’d like you to make for me for the door step light. I’m in canada so I’d like to avoid the long distance if we can pls sir.
Email is joshuascartown@hotmail.com
Mr. Kustom Support (verified owner) –
yes you can send you logo to sales@mrkustom.com
Daniel Ward –
How do I know if the design I want is “print ready”? Or as long as it’s a PNG file, its fine?
Mr. Kustom Support (verified owner) –
The image should be 1000pc in width and should clear enough in order to make the door projector.
Ahmad Richardson (verified owner) –
Very good product